GERBANG OTOMATIS DENGAN PENGUKURAN SENSOR MLX90614 BERBASIS ARDUINO SEBAGAI ALAT PENCEGAHAN PENULARAN AWAL COVID-19

Sulis Sutiono; Magdalena Simanjuntak; Nurhayati

doi:10.61722/jipm.v2i3.229

Authors

Sulis Sutiono Sekolah Tinggi Manajemen Informatika dan Komputer (STMIK) Kaputama Binjai
Magdalena Simanjuntak Sekolah Tinggi Manajemen Informatika dan Komputer (STMIK) Kaputama Binjai
Nurhayati Sekolah Tinggi Manajemen Informatika dan Komputer (STMIK) Kaputama Binjai

DOI:

https://doi.org/10.61722/jipm.v2i3.229

Abstract

Maintaining health is very important for life, especially during the current covid-19 pandemic. One of the protocols imposed by the government for people who are active in public spaces or open facilities is to check their body temperature. In this study, a design for preventing the initial transmission of covid-19 was made with an arduino-based body temperature which has an automatic door if the body temperature is above 37.30 the door will not open and if it is below normal the door will also not open. This tool for preventing the initial transmission of covid-19 uses the MLX90614 sensor to measure temperature in units of celsius (0c). Body temperature data is also displayed on the 16x2 (cm) lcd on the device. The test results of measuring body temperature are compared with a thermo gun. This automatic gate with arduino-based mlx90614 sensor measurement as a prevention tool for early covid-19 transmission is expected to be installed in public places that require inspections of people who will be active in the room, the operator can stand at the control desk so that there is no direct contact with the public .

References

Andrianto,H dan Aan, 2017, ARDUINO Belajar Cepat dan Pemrograman, Penerbit Informatika, Bandung.

Goda Vasantharao., SK Arifunneesa. (2020). Temperature Detection and Automatic Sanitization and Disinfection Tunnel-COVID 19. The International journal of analytical and experimental modal analysis, XII (VI), 1175-1181.

Jawas, H., N.M.A.E.D, Wirastuti., & Widyadi, S. (2018). Prototype Pengukuran Tinggi Debit Air Pada Bendung Dengan Menggunakan Sensor Ultrasonik Berbasis Arduino Mega 2560, E-Journal SPEKTRUM, 5(1), 1-4.

Kadir,A, 2016, Simulasi ARDUINO, Penerbit PT Elex Media Komputindo, Jakarta.

Sitorus, L. 2015, Algoritma dan Pemrograman, Yogyakarta..

Sokku, S, R., & Sabran, F, H. (2019). Deteksi Sapi Sehat Berdasarkan Suhu Tubuh Berbasis Sensor MLX90614 dan Mikrokontroller, Prosiding Seminar Nasional Lp2m UNM, 613-617.

Utami, Y, N., R.Rumani., & Nurfitri, A. (2015). Speaker Recognition Design Based On Lamp Control System Microcontroller, e-Proceeding of Engineering, 2(2), 3332-3346.

Wahyudi, A., Fathorazi,N,F., & Syaiful. (2020). Pemanfaatan Radio Frequency Identification (RFID) Berbasis Internet of Things (IoT) untuk Perancangan Palang Pintu Otomatis di Universitas Nurul Jadid, Journal of Community Engagement,1(2),117-130.

Widiana, I, W, Y., I Gusti, A, P, R, A., & Pratolo, R. (2019). Rancang Bangun Kendali Otomatis Lampu Dan Pendingin Ruangan Pada Ruang Perkuliahan Berbasis Mikrokontroler Arduino Nano, Jurnal SPEKTRUM, 6(2), 112-120.

Wulandari, R. (2020). Rancang Bangung Pengukur Suhu Tubuh Berbasis Arduino Sebagai Alat Deteksi Awal Coid-19, Prosiding SNFA,183-189.